specifications dimensions t 1 in case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125 c . t 2 refer to page 56 for reflow soldering conditions. (unit : mm) size list 20 rv : rated voltage (sv) : surge (125 c ) d l p r c w 0.2max. h the svqp series guaranteed 125 c i j h i w p m u b h f s f t j t u b o d f x b t j n q s p w f e u p b s b u f e n b y j n v n p g 7 this product is very reliable, guaranteeing 85 c 85% performance. suitable for use in smoothing circuits of vehicle- mounted equipment, industrial equipment, etc. this product can support lead free-reflow.( t 2). 4 q f d j g j d b u j p o t g p s f b d i t f s j f t 4 . specifications for each series marking : polarity( ), rated voltage, (purple) svpd rated capacitance, lot.no. t for the minimum packing quantity, please refer to page 55. conductive polymer type svpd series guaranteed at 125 c, 85 c 85% guaranteed,rated 35v, rated 35v max. c6 e7 f8 e12 f12 d 0.5 6.3 8.0 10.0 8.0 10.0 l w 0.2 5.9 6.9 7.9 11.9 12.6 h 0.2 6.6 8.3 10.3 8.3 10.3 6.6 8.3 10.3 8.3 10.3 c 0.2 7.3 9.0 11.0 9.0 11.0 r 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.8 to 1.1 0.8 to 1.1 p 0.2 2.1 3.2 4.6 3.2 4.6 size code rv sv f 10.0 11.5 16.0 18.4 25.0 29.0 35.0 40.0 8.2 10 18 22 39 47 56 82 e7 c6 e7 f8 e12 f12 e7 f8 e12 f12 c6 +0.1 -0.4 items conditions characteristics -55 c to +125 c m : 20% less than or equal to the value of table2 less than or equal to the value of table2 less than or equal to the value of table2 within 20% 2 times or less than an initial standard 2 times or less than an initial standard below an initial standard within 20% 2 times or less than an initial standard 2 times or less than an initial standard below an initial standard within 10% 1.3 times or less than an initial standard 1.3 times or less than an initial standard below an initial standard (after voltage processing) category temperature range tolerance on rated capacitance tangent of loss angle leakage current esr endurance damp heat (steady state) characteristics of impedance ratio at high temp. and low temp. -55 c +125 c ? c/c tan esr leakage current ? c/c tan esr leakage current ? c/c tan esr leakage current resistance to soldering heat z / z 20 c z / z 20 c 0.75 to 1.25 0.75 to 1.25 120hz 120hz based the value at 100khz | +20 c 125 c, 2,000h, rated voltage applied 85 c, 85 to 90% rh, 1,000h, rated voltage applied (vps) (230 c x 75s) after 2 minutes t 1 t 2 www.datasheet.co.kr datasheet pdf - http://www..net/
21 table2 svpd series characteristics list t 1 capacitance tolerance : m 20% t 2 after 2 minutes t 3 tx : ambient temperature 25svpd10m 10svpd56m 35svpd8r2m 25svpd22m 16SVPD82M 35svpd18m 25svpd39m 35svpd22m 25svpd47m 35svpd47m 25svpd82m 25 10 35 25 16 35 25 35 25 35 25 10 56 8.2 22 82 18 39 22 47 47 82 65 45 70 48 40 60 45 50 30 30 28 474 538 400 580 670 550 664 700 943 1150 1202 1500 1700 1300 1835 2120 1800 2100 2300 2980 3650 3800 0.10 0.12 0.10 0.10 0.12 0.10 0.10 0.12 0.12 0.12 0.12 50 112 57 110 262 126 195 154 235 329 410 size code 4 q f d j g j d b u j p o t g p s f b d i t f s j f t 4 . specifications for each series part number t 1 tangent of loss angle (max.) leakage current ( a) (max.) t 2 rated voltage (v) rated capacitance ( f) esr 100khz to 300khz (m ? ) (max.) 100khz (marms) rated ripple current allowable ripple current ?? 5 y? ? 5 y? ? recommended land pattern dimension of pwb (unit : mm) c a b t 3 frequency coefficient for ripple current frequency coefficient 120hz ? f ? 1khz 0.05 1khz ? f ? 10khz 0.3 10khz ? f ? 100khz 0.7 100khz ? f ? 500khz 1 e7 f8 e12 f12 c6 c6 e7 f8 e12 f12 ab c 2.1 2.8 4.3 2.8 4.3 9.1 11.1 13.1 11.1 13.1 1.6 1.9 1.9 1.9 1.9 size code www.datasheet.co.kr datasheet pdf - http://www..net/
|
